By Central Valley Water Restoration Published
How to Get Rid of Mold for Good: Fix the Moisture First
Cleaning mold off a surface is the easy part. Keeping it off is the real job. The EPA says the key to mold control is moisture control, and it advises fixing plumbing leaks and other water problems as soon as possible and drying all items completely. If the water problem is not fixed, the mold will come back.
So before you pick up a brush, find out why the area got wet. A slow leak, a damp wall, a surface that never dries after a shower, or a water event that was never fully dried out can all feed mold. Stop the source first, then clean.
The rest of this guide follows the EPA and CDC guidance for a small, visible patch: how to decide whether it is yours to handle, how to protect yourself, how to clean hard surfaces, what to throw away, what does not work, and when to stop.
Decide Whether This Is a Job You Can Do Yourself
The EPA says that if the moldy area is less than about 10 square feet, roughly a 3 by 3 foot patch, you can in most cases handle it yourself. With a lot of water damage or more than 10 square feet of mold, the EPA's professional remediation guidance applies instead.
Before you start any cleanup, check for hazards, in this order:
- People first. If there is fire, smoke, a gas smell, sparking or buzzing electrics, or a sagging or bulging ceiling, get everyone out and call 911.
- Gas. If you smell gas, leave and call from outside. Do not turn on lights or do anything that can cause a spark (CDC).
- Electricity. Never touch a panel, switch or cord while standing in water or on a wet floor. If you would have to enter standing water to reach the power switch, call an electrician (CDC).
- Water. Only when the first three are clear, stop the water at its source, and only if you can reach it without standing in water near electrics.
Only after that do you look at the mold itself. Here is a simple way to sort the two outcomes.
You can usually clean it yourself when:
- The mold is visible and covers less than about 10 square feet.
- It is on a hard surface that you can scrub and dry completely.
- The cause is found and fixed, and no one in the home is in a higher-risk group.
Stop and call a professional when:
- The mold covers more than about 10 square feet or there is a lot of water damage.
- The mold followed a flood or a sewage backup.
- You smell mold but cannot see it. The EPA says to consider hiring an experienced professional for hidden mold.
- Anyone in the home has asthma, a mold allergy, a weakened immune system or chronic lung disease. The CDC lists these groups as at higher risk, and Ready.gov advises them to avoid buildings with mold.
If you are not sure which list you are on, treat it as the second one. If what you found looks like black mold, it has its own guide: how to get rid of black mold.
Protect Yourself Before You Start
The CDC advises wearing protective equipment when you clean mold: gloves, an N95 mask or better, and goggles. Open doors and windows while you work so fresh air moves through the space.
Keep children and pets out of the room. Do not start if you or someone helping you is in one of the higher-risk groups above.
How to Clean Mold Off Hard Surfaces
The EPA's method is plain. Scrub mold off hard surfaces with detergent and water, then dry the surface completely. The CDC adds two points: remove all the mold you can see, and dry the surface right away.
- Step 1: Put on your gloves, N95 mask and goggles, and open the windows.
- Step 2: Scrub the mold off the surface with detergent and water.
- Step 3: Remove all the mold you can see.
- Step 4: Dry the surface completely and right away.
- Step 5: Watch the spot afterward. If the mold comes back, look for the moisture source again.
What About Bleach?
Many people reach for bleach first. The EPA does not recommend using a biocide such as chlorine bleach as a routine practice during mold cleanup. Dead mold can still cause allergic reactions, and it has to be removed anyway.
The sources differ a little here. The CDC page also describes cleaning mold with a mix of bleach and water, while the EPA does not recommend bleach as routine practice. This guide follows the EPA's detergent-and-water method as the main instruction. If you do use bleach, follow the label, ventilate the area, and never use it in a closed space. Never mix bleach with ammonia or any other cleaner (EPA and CDC). For more on this, see does bleach kill mold.
Vinegar, Hydrogen Peroxide and Other Home Remedies
The EPA and CDC cleanup guidance does not call for vinegar, hydrogen peroxide or other home remedies. The method they describe is scrubbing with detergent and water, then drying. This guide makes no claims for any product. The most common one has its own post: does vinegar kill mold.
What to Throw Away Instead of Cleaning
Some materials are not worth saving. The EPA says absorbent or porous materials such as ceiling tiles and carpet may have to be thrown away if they become moldy. Mold can grow into the empty spaces and crevices, and it may be impossible to remove completely.
For anything wet with floodwater, the CDC says to take out what cannot be cleaned and dried completely within 24 to 48 hours.
Each material has its own limits. These guides go through them one at a time:
- Mold on walls and when drywall must go
- Mold on wood furniture, trim and framing
- Mold on carpet and when to replace it
What Does Not Fix Mold
A few common moves look like fixes and are not.
- Painting or caulking over it. The EPA says not to paint or caulk moldy surfaces. The CDC says painting or caulking over mold will not prevent it from growing.
- Ozone generators. The EPA says that at concentrations that do not exceed public health standards, ozone does not effectively remove mold, and inhaled ozone can damage the lungs.
- Killing it without removing it. Dead mold can still cause allergic reactions, so it has to come off or come out.
- Air cleaning alone. Cleaning the air is not the same as removing the mold. The guide on air purifiers and mold explains the limits.
Keep Mold From Coming Back
The EPA advises drying water-damaged areas within 24 to 48 hours and keeping indoor humidity below 60 percent, ideally between 30 and 50 percent. Fix leaks as soon as you find them, and do not leave wet materials sitting.
For a full list of habits that keep mold out, read how to prevent mold in your house.
When to Stop and Call a Mold Professional
Stop cleaning and call a professional if any of these is true:
- The mold covers more than about 10 square feet.
- It keeps coming back after you have cleaned it and dried the area.
- You smell mold but cannot find it.
- The mold followed a flood or a sewage backup.
- Someone in the home is in a higher-risk group.
For suspected hidden mold, the EPA says to consider an experienced professional, and an inspection may include sampling. Sampling can also confirm that an area was cleaned properly. That testing is done by an independent industrial hygienist, not by a remediation company. The guide on testing for mold in a house explains when it makes sense.
If the job is past a small, visible patch, mold removal is the work we do. We are an IICRC Certified Firm, and our estimates are free. Read about professional mold removal, or call us at (559) 999-1447. The line is open 24/7, and a real person answers.
About Central Valley Water Restoration
Central Valley Water Restoration is a father-and-son restoration company in Fresno, California. IICRC-certified in water damage restoration, applied structural drying and applied microbial remediation. Water, mold, fire and smoke, sewage and storm damage across Fresno, Madera, Tulare, Kings, Mariposa and Merced counties. Reconstruction and repairs are completed by our licensed general contracting partner, Gostanian General Building Corp, CSLB Lic. #346866. Financing options available — ask us for details.
More about Central Valley Water RestorationContact Central Valley Water Restoration
